images cutting cast iron toilet pipe

For troubleshooting tips when you're cutting a cast iron pipe, keep reading! Proper venting will also be important, and a cleanout is required either before it leaves the basement, or at grade just outside the building. Alternatively, you could frame a wood floor to the height of your pipes. For my plumbing to flow correctly, I need to tie in at the lowest point of that sanitary line where it runs horizontal under the footing and install a Wye connection for my new bathroom requirements. Method 1. Had a half bath where the 61 yr. You may need to score the pipe several times before you can make the final cut. What's a good way to cut cast iron pipe in a tight space? Together, they cited 6 references. It's going to depend on whether or not the old pipe is secured already.

  • plumbing How do I cut cast iron rough sewage pipe Home Improvement Stack Exchange
  • What's a good way to cut cast iron pipe in a tight space This Old House

  • When cutting cast iron pipe, I used a Lenox 9 inch diamond recip saw blade that has tangs on both ends, so you can switch ends when one section gets dull. How to Cut Cast Iron Pipe. Cast iron pipes were used before the invention of PVC pipe and was the choice for main stacks and waste drains. Cast-iron pipe can be cut with a rented snap cutter or a reciprocating saw or a grinder with a diamond blade or cutting wheel.
    I used nearly all the water to cool the wet towel in pipe, and rewet others.

    Video: Cutting cast iron toilet pipe Fastest Way to Cut Cast Iron Pipe

    Of course you would either have to raise the bath floor 6" or cut the concrete a install a below-ground system. Awesome picture!

    plumbing How do I cut cast iron rough sewage pipe Home Improvement Stack Exchange

    Any suggestions? How do I go about cutting them to install a toilet and a shower? Not Helpful 0 Helpful 9. If you are forced to cut on the face of the pipe where it will pinch the blade, make a half cut with the cutting blade, switch blades to a grinding blade, open up the cut so it is wider, and then switch back to the cutting blade to finish the cut.

    images cutting cast iron toilet pipe
    SAUCER OF ZILK TPB SEASON
    I once identified an item as cast iron ,not steel, by how easily I drilled a hole in it.

    Related 7. To be flush with the concrete floor. Not Helpful 1 Helpful 1. A diamond wheel in an angle grinder is another possibility.

    I'm putting in a basement bathroom, I've broken the concrete floor open and located my sanitary line. For my plumbing to flow correctly, I need to tie in at the. Cast iron pipes for shower and toilet are about 4 in. out of floor.

    Video: Cutting cast iron toilet pipe replacing a section of cracked cast iron drain pipe in 20 minutes

    How do I go about cutting them to install a toilet and a shower? To be flush with the concrete floor. With a DIY plumbing repair, you need to know how to cut cast iron pipe. There are 3 ways: a hacksaw, cold chisel, or snap cutter. See which one is best for.
    To be flush with the concrete floor.

    In many older homes, cast iron wasn't secured to anything, in which case you will want to double wrap rope around pipe and secure above the area you are cutting. Of course you would either have to raise the bath floor 6" or cut the concrete a install a below-ground system.

    Since that was not what you asked about, the best choice is probably a 4" angle grinder. I once identified an item as cast iron ,not steel, by how easily I drilled a hole in it. Not Helpful 0 Helpful 9.

    images cutting cast iron toilet pipe
    Forno rex fq 53 x 74
    Ensure that there are as many cutting wheels as possible against the pipe.

    images cutting cast iron toilet pipe

    Did this article help you? Custom Filters release announcement.

    What's a good way to cut cast iron pipe in a tight space This Old House

    Awesome picture! Hope that helps. If you can dig down to the line outside the foundation probably not possible in northern areas this time of yearcut it outside, then add a stub to the sweep tee you'll be putting in so you don't have to work under the footing. That is, add a 2-foot or so stub to the outlet of the tee before you stick it under the footing.


    Had a half bath where the 61 yr.

    Hot Network Questions.

    images cutting cast iron toilet pipe

    Post as a guest Name. Apply pressure onto the handles of the cutter so the wheels cut into the pipe.

    Pat Pat 16 2 2 bronze badges. I would remove what is there and rework the configuration to some thing that does work.

    images cutting cast iron toilet pipe
    Toronto the second city comedy
    Finish the job with a flap disc, which will allow you to get in nice and close with good control.

    Email Required, but never shown. Home Questions Tags Users Unanswered.

    images cutting cast iron toilet pipe

    Why is it important that you cut them flush to the concrete? To create this article, 11 people, some anonymous, worked to edit and improve it over time.

    0 Replies to “Cutting cast iron toilet pipe”